Differences

This shows you the differences between two versions of the page.

--- drawingboard:components:propulsion:ground [2024/06/05 23:03] – tailkinker
+++ drawingboard:components:propulsion:ground [2024/06/05 23:58] (current) – tailkinker
@@ Line 5: / Line 5: @@
 To determine how large a motive drive-train you need, you must first decide how fast you want your vehicle to be.  Choose a top speed in kilometers per hour.  To find the power required for your desired speed, multiply the speed by itself, and then by the mass of your vehicle (in tonnes).  Then divide by the suspension factor (SF) for your motive drive-train, as found on the table below.
-^  TR  ^Type    ^   SF  ^  Mass (kg)             ^  Cost (\[ce])  ^
+^  TR  ^Type    ^    SF   ^  Mass (kg)              ^  Cost (\[ce])   ^
-|  -5  |Skids   |   90  |  --                    |  --            |
+|  -5  |Skids        |    90   |  \[dg]                  |  \[dg]          |
-|  -4  |Wheels  |  160  |  1.8 \[mu] Power + 36  |  Mas \[mu] 10  |
+|  -4  |Wheels       |   160   |  1.8 \[mu] Power + 36   |  Mass \[mu] 5   |
+|  -2  |Wheels       |   360   |  1.8 \[mu] Power + 36   |  Mass \[mu] 5   |
+|  -1  |Wheels       |   650   |  0.9 \[mu] Power + 18   |  Mass \[mu] 5   |
+|   0  |Wheels       |   650   |  0.45 \[mu] Power + 9   |  Mass \[mu] 5   |
+|  -1  |Half-tracks  |   360   |  1.7 \[mu] Power + 40   |  Mass \[mu] 8   |
+|   0  |Half-tracks  |   500   |  1 \[mu] Power + 20     |  Mass \[mu] 8   |
+|  -1  |Tracks       |   250   |  2.5 \[mu] Power + 60   |  Mass \[mu] 10  |
+|   0  |Tracks       |   360   |  1.5 \[mu] Power + 30   |  Mass \[mu] 10  |
+|  -1  |Ski-tracks   |   160   |  2.5 \[mu] Power + 60   |  Mass \[mu] 10  |
+|   0  |Ski-tracks   |   360   |  1.5 \[mu] Power + 30   |  Mass \[mu] 10  |
+|   0  |Legs         |  \[dd]  |  2.7 \[mu] Power + 120  |  Mass \[mu] 25  |
+|  +1  |Legs         |  \[dd]  |  1.35 \[mu] Power + 60  |  Mass \[mu] 25  |
+|  +2  |Legs         |  \[dd]  |  0.5 \[mu] Power + 30   |  Mass \[mu] 25  |
+\[dg]Skis cannot be powered, but are included here for their Suspension Factor.\\
+\[dd]Regardless of TR, suspension factor is 160 for two legs, 250 for three legs or 360 for four or more legs.
+To determine the volume of any drive-train, divide its Mass, in kilograms, by 150.  This will give its volume in cubic meters.  For a Legs drive-train, this volume must be split equally between all legs.
+===== Power Requirements =====
+Most of the above drive-trains require a powerplant to operate.  As long as your powerplant can deliver the required power, you're good to go.
+But what if you don't feel like using a direct powerplant?  Maybe you're building a land-sailer, or a jet-propelled car.  Maybe you need to know how fast your airplane can taxi, in order to make sure it can reach take-off speed.
+You can use the Power formula backward, in order to find your land speed based on power delivered.  However, you only receive full power for direct drive of your ground drive-train, or for animals towing your vehicle.  For every other source of power, divide the delivered power by four.
+To determine your land speed, multiply the power by your Suspension Factor, then divide by your vehicle's mass.  Find the square root of this value.  Drop fractions.
+===== Animal Power =====
+Yes, you can tow a vehicle behind animals.  The biggest down-side to doing this is that the top speed cannot exceed that of the slowest animal pulling the vehicle.
+To find the power of the towing animals, go to the [[drawingboard:fundamentals:scale|Scale]] table.  Find each animal's mass, in kilograms, on the Volume column, then read across to the Linear entry.  Total these values for all attached animals, and then divide by 40.  Yes...it won't be a lot.
+===== What About Hovercraft? =====
+Technically speaking, hovercraft are not ground vehicles.  They are very low-flying aircraft.
+Build your hovercraft as though it were an aircraft, but install some sort of Lift Equipment to counter out its mass entirely.  For a TR-1 or TR0 hovercraft, a lift skirt or wing in ground effect will do the trick.  For a more advanced hovercraft, take a look at gravity drives.